Community : Thread List - Flextone / HD147 / Duoverb / AX2

My HD 147 Head Has Low Volume, Any Ideas?

support@line6.com — Sun, 22 Nov 2009 05:08:21 GMT

It is connected to a Marshall 4 X 12

How to run Ipod into HD147 for playing along with?

support@line6.com — Fri, 20 Nov 2009 20:54:02 GMT

Hi,

I am a new owner of the Line 6 HD147 and I was wondering if there were any suggestions on how to make an auxillary device such as an Ipod work with the HD147 in the same manner the 1/8" input does on the Spider series amps. I do not have a stereo for playback and always used the auxillary input on my old Spider III amp to play along with recordings, and I just became accustomed to this way of doing it. Any and all suggestions would be greatly appreciated on how to defeat this issue.

Thanks,

JAM

previewing custom tone

support@line6.com — Sat, 21 Nov 2009 02:59:20 GMT

Can custom tones be previewd before downloading? Would the tones be accessible simply by adjusting the knobs on the amp or is "deep editing" needed?

HD 147 Cab decision

support@line6.com — Tue, 17 Nov 2009 22:32:35 GMT

Hi,

I just purchased a HD147 head and found out that the 412S cabs that went with these heads are now discontinued. What should I do in order to get a stereo 150w per side cab?

Thanks,

Joe

Flextone II HD with 2 mono 8 ohm cabinets

support@line6.com — Tue, 17 Nov 2009 17:59:09 GMT

If I connect two cabinets (1=Flextone 412s set to 8 ohms, left/mono input; 2=Rocktron 112 8 ohm wedge for a guitar only monitor) and connect the two to the two left/mono output of the Flextone II HD set to 8 ohms, will this cause any problems? In other words, if the head is set to 8 ohms, does connecting a load to the two left outputs but nothing to the right outputs affect impedence, etc? I'm trying to find a creative solution to overpowering smalls rooms versus not being able to hear myself without being dependent of the sounds guy to get the monitor mix right. Thanks!

Flextone II floorboard malfunction

support@line6.com — Sat, 14 Nov 2009 05:04:17 GMT

I have a Flextone II set up. In the last year I've gone thru 2 floorboards. They keep getting stuck in "Edit Mode" and the tone changes !!!

The amp works fine when the floorboard is unplugged. Now, less than 18 months after buying the second one, it's doing the exact same thing. Is there a switch that wears out faster than others and needs to be replaced? Could it be the Amp and not the floor board? How can I test it? We have settings and special tones that we can't afford to loose. What do I do?

Question

support@line6.com — Tue, 17 Nov 2009 19:25:10 GMT

My line 6 flexitone 111 xl plus loses volume after a few minutes which has the affect of losing tone. Can this be fixed if so how. Will having a service fix this problem

Intermittant problem with AX2 losing power. Ideas??

support@line6.com — Sun, 15 Nov 2009 18:42:52 GMT

Hey line 6 fans and techies,

I have a problem with my AX2 212 I have had for several years now. Haven't used it since it died in 2005, but it's been sitting in the basement waiting for me to get it fixed. Yeah, I have been procrastinating for quite some time, and have since had several amp/cab setups. I just would like to get it going for a practice amp here in the basement.

Here is how the problem started.....One day at practice, I went to turn the amp on and a bunch of funky stuff was on the amps display, as well as the floorboard. No matter what I did, nothing changed. Tried hitting footswitches, turn knobs, turn off and on again, and same result. Tried hard reset, and still nothing. Then after being on for awhile, both displays will shut off completely. I would shut off and turn back on again, and still no power on display. Leave it sit for several days, and it will power up and I can play through it for about 1 minute before it dies again. Seems like a cold solder joint, or something funky in the board? I have no idea where to start checking it. Obviously it is temperature related, since once it warms up, it shuts down. Anyone have any ideas? I have a line 6 service center about an hour and a half away, but I'm not even sure if they work on amps this old still. This thing is from the late 90's, and probably considered obsolete to fellow line 6 users. Or maybe not? Any advice or ideas are greatly appreciated. I will probably end up sending it to the service center, but I'd like to figure it out for myself with some tests. Maybe using a heat gun, and some of that aerosol spray that freezes, to see if I can get the problem to come and go that way. Thanks in advance!

-Jason

Help on Hooking a Flextone III directly to my Computer?

support@line6.com — Tue, 17 Nov 2009 19:02:53 GMT

HI have a Flextone III amp, and I'm looking to start recording music through my computer, so I need to know exacly what cords I would need to buy and where to plug those cords in. If the quality of sound depends on whether I buy a cheap cord or an expensive one, then I would like to know that too, because I want to get the best quality I can afford. Thanks for your help in advance.

Josh

registration issues

support@line6.com — Thu, 12 Nov 2009 00:24:16 GMT

hi i have inherited my line6 flextone 3 from my deceased grandfather, i have downloaded the line6 monkey and line 6 edit and niether will recognize my product. i registered it but the serial number identifies it as a flextone 3 xl ((21)f3x1p5535002877) by the input it only says flextone iii. i registered it as a flextone 3 xl but with it being registered that way the software still does not recognize the correct amp. can you please help me? thank you!

james gardner

flextone 2hd

support@line6.com — Wed, 04 Nov 2009 19:12:55 GMT

Salve , avevo bisogno di chiedervi come si puo' togliere sulla FLOOR BOARD la lettera R 1 -

IO HO LA FLEXTONE 2HD USANDO IL PROGRAMMA PER PC HO MOSSO QUESTA LETTERA CHE ORA NON SO' COME TOGLIERE .

PIU' PRECISAMENTE SUL BANCO NR1 MI DA' LA SIGLA - R 1 E COSI' VIA !!

GRAZIE ERIK

BE ON THE FLOOR BOARD FLEXTON 2HD COMPARE ON FLOOR LETTER - R - 1 COME ON BANCO DO TO REMOVE THIS? THANKS